Search Results

Filter By

Singapore Standards Package/Series ISO IEC

430 publications found under "tr iec/ts 62600"

SS 254-0:2001 [Withdrawn]

Electrical apparatus for explosive gas atmospheres - General requirements (Users can refer directly to relevant parts of IEC 60079)

...trical apparatus for potentially explosive atmospheres is divided into the following: Group I: electrical apparatus for mines susceptible to firedamp; Group II: electrical apparatus for places with a potentially explosive atmosphere, other than mine...
...Electrical apparatus intended for mines where the atmosphere, in addition to firedamp, may contain significant proportions of other flammable gases (i...
...other than methane); it shall be constructed and tested in accordance with the requirements relating to Group I and also to the subdivision of Group II corresponding to the other significant flammable gases...

SS 254-1:2001 [Withdrawn]

Electrical apparatus for explosive gas atmospheres - Flameproof enclosures (Users can refer directly to relevant parts of IEC 60079)

...For electrical apparatus of Group IIC, the cone angle shall not exceed 5...
...trical apparatus of Group IIC Flanged joints are not permitted for electrical apparatus of Group IIC intended for use in potentially explosive atmospheres containing acetylene except if the gap is 0,04 mm for L 9,5 mm up to 500 cm 3...
...2 based on the manufacturers maximum constructional gap, i C...

SS 254-14:2005 [Withdrawn]

Electrical apparatus for explosive gas atmospheres - Electrical installations in hazardous areas (other than mines) (Users can refer directly to relevant parts of IEC 60079)

...transformers and safety isolating transformers Requirements IEC 61024-1:1990, Protection of structures against lightning Part 1: General principles IEC 61024-1-1:1993, Protection of structures against lightning Part 1: General principles Sectio...
...truction, installation and use of apparatus NOTE For the purposes of this standard, an area is a three-dimensional region or space...
...4 non-hazardous area area in which an explosive gas atmosphere is not expected to be present in quantities such as to require special precautions for the construction, installation and use of apparatus 3...

SS 254-2:2002 [Withdrawn]

Electrical apparatus for explosive gas atmospheres - Pressurized enclosures 'p' (Users can refer directly to relevant parts of IEC 60079)

...SS 254 : Part 2 : 2002 16 5 Constructional requirements for pressurized enclosures 5...
...2 of IEC 60079-0, or be interlocked so that the electrical supply to apparatus not protected by a type of protection listed in 7...
...trical supply to electrical apparatus not protected by a type of protection given in one of the other standards listed in the IEC 60079-0 is disconnected automatically when they are opened and so that the supply cannot be restored until they are close...

SS 254-6:2003 [Withdrawn]

Electrical apparatus for explosive gas atmospheres - Increased safety “e” (Users can refer directly to relevant parts of IEC 60079)

...tricity or electric charge, which a fully charged battery can deliver under specified conditions NOTE The SI unit for electrical charge is the coulomb (1 C = 1 As) but in practice, battery capacity is usually expressed in ampere-hours (Ah)...
...14 container (of a cell) container for the plate pack and electrolyte of a cell made of a material impervious to attack by the electrolyte [IEV 486-02-20] 3...
...17 partition wall integral part of a battery container dividing it into individual sections and increasing its mechanical strength SS 254 : Part 6 : 2003 15 3...

SS 263-1:2010 [Withdrawn]

Specification for luminaires - General requirements and tests (Replaced by SS IEC 60598-1:2016)

...SS 263 : Part 1 : 2010 15 COPYRIGHT LUMINAIRES Part 1: General requirements and tests 0 SECTION 0: GENERAL INTRODUCTION 0...
...1 Scope and object This Part 1 of International Standard IEC 60598 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V...
...The requirements and related tests of this standard cover: classification, marking, mechanical construction and electrical construction...

SS 272:2022 [Current]

Specification for unplasticised PVC pipes and fittings below ground for sanitary drainlines

...1 CEN, reproduced with permission from EN 1401-1:2019 SS 272:2022 15 COPYRIGHT Table 5 Minimum radius (R) for long bends made from extruded pipe 7...
...NOTE The Z-lengths are intended to assist in the design of moulds and are not intended to be used for quality control purposes...
...Where a fitting or adaptor provides for a transition between two nominal sizes, the wall thickness of each connecting part shall conform to the requirements for the applicable nominal size...

SS 280-1:2006 [Current]

Frame scaffoldings

...After removal of the test load the member or structure shall be deemed to have adequate stiffness if all measured strain or deflection values show a recovery of at least 80%...
...If any measured strain or deflection value does not show a recovery of at least 80% of the respective maximum value recorded during the two hours under load, the test shall be repeated...
...2 Strength test When tested in accordance with Annex A...

SS 280-2:2009 [Current]

Specification for metal scaffoldings - Modular scaffoldings

...0 kg (distributed load) (width of platform) (length of platform) A...
...4 Strength test load (4149...
...5 m Tie to rigid structure L/2 NOTE A, B, C, D, E, F are the locations where the transverse and longitudinal deflections are measured...

SS 30:1999 (2012) [Confirmed]

Manhole tops and surface-box tops

...5 N/mm 2 ; and (b) it provides an adequate contribution to stability under working conditions...
...NOTE The specifier may require a frame deeper than 100 mm, appropriate to the particular traffic flow characteristics of the method of installation (see Clause 9)...
...3 Preparation for the test The test block shall be placed on the unit with its vertical axis perpendicular to the surface and coincidental with the geometric centre of the cover (examples, see Figure 9)...

Page 2 of 43